Question:
Discuss about the effect of the material acoustic impedance on two major scenarios.
The propagation of small sound pressure waves through a medium is termed as acoustics. The area has been of great interest to the scholars as attempts are made to scientifically uncover the key aspects of the propagation phenomenon. Notably, acoustic impedance is among the issues that research scientists have focused their energy to develop the concept further with the intention to explain how the phenomenon occurs and the various parameters that can affect it for a given material. In this brief study, great attempts are made to determine the methods and applications involved. Classical deterministic models are often used to mathematically draw a scenario of acoustic impedance and how it depends on the frequency. In this paper, therefore, two methods with accompanying practical applications will be elucidated; such methods as the ultrasound with applications in the spatial compounding. Now, there are two major applications alongside the methods that are currently in use. Therefore, the aim of this paper is to uncover the fundamental principles and practice in the study of acoustic impedance. Certainly, the paper will greatly serve as a substantive material in the furtherance of acoustic impedance concept in the practical world.
The 2-microphone transfer function
This method is implemented using an impedance tube with two microphones situated at positions whose distance apart is known. The concept is as follows: An incident wave is propagated from loudspeaker and a reflected wave result. The standing-wave phenomenon can then be used to measure various characteristics like impedance, wavelength and frequency. It should be noted that the tube is in-situ in the set up. The plane wave is made to travel in the duct and the frequency is limited by the geometric properties of the tube such as diameter and speed of sound in air. Mathematically, the upper limit frequency, according to Chalmers (2012) must be:
Fu<0.58Co/d….(1)
The speaker will act as a source of sound wave and the incident pressure wave is denoted PR
Notably, the complex sound pressure at the microphone position is given by:
P1= P1(x1) + PR(x1)= P1e-jkx1 + PRejkx1……(2a)
P2= P1(x2) + PR(x2)= P1ejkx2 + PRe-jkx2
The microphone would then detect the signals (both the incident and reflected pressure waves).
However, due to internal amplitude and phase between the microphones, the microphone interchange method can be used to minimize this mismatch (Chalmer, 2012). Finally, the transfer function of both the incident and reflecting waves between the microphones can be derived using the general equations 3(a) and 3(b):
H1= P1(x2)/P1(x1)= P1e-jkx2/P1e-jkx1= ejks…3(a)
HR= PR(x2/PR(x1)= PRejkx2/PRejkx1= e-jks…3(b)
Where s=x2-x1
The reflection coefficient R can then be determined (which is actually the ratio of the complex reflected and incident pressures.
Rx=x1= H12-H1/(HR– H12)…(3)
But note that there is normally a portion of the incident propagating wave that is not reflected but absorbed, that is given by:
α = 1-/R/2….(4)
The surface acoustic impedance is therefore give as:
Zs= Zo(1+R)/(1-R) where Zo= PoCo acoustical characteristics impedance of air
The acoustical impedance is affected by the source frequency such that low frequency sources result in lower impedance intensity hence reduced impedance level. However, best performance of the set up occurs at a particular low frequency region as given by equation 1. Besides, the diameter of the tube plays a pivotal role on the frequency range allowable in the method. Higher frequency above the given limit is often constrained by the tube diameter.
In the previous method, consideration was made for plane waves only hence the model is limited to certain applications. However, here the wave decomposition method can cover the oblique-incident and normal pressure waves hence applicable to higher modal order modes (Schultz, Cattafesta & Sheplak, 2006). The method depicts a one-dimensional lined duct with an excitation speaker at one end and impedance boundary on the other end. There is normally a material that will be inserted at the duct-end such that during propagation, the material produces, in part, a reflective and reactive boundary hence complex transfer function results.
Mathematically, dU/dx(L, t)= -k(1/c)dy/dt(L,t)….(5)
Where k= complex acoustic impedance
X= L,U(L,t)= fluid particle displacement at x=L
C= sonic wave speed in the duct (m/s)
t = time variable
x= spatial variable (m)
L= length of the duct (m)
Hence equation 2 illustrates how the impedance can be determined using the method once the experiment is performed:
Re(T)+iIm(T)= Re(k) cos [w/c(x-L)+i{Im(k)Cos{w/x(x-L)-sin[w/c(x-L)/Re(k) Cos (w/cL)+i{Im(k)cos(wl/c)+sin(wl/c)}…(6)
The acoustic pressure of the system is proportional to the spatial derivative of the particle displacement
P(x,t)= -pc2dU/dx(x,t)
The turbofan engine acoustic
The two-microphone transfer function method can be used in the turbofan engine to analyze the material acoustics making up the compressor and the turbine.
The model first considers the system to be such that the phenomenon occurs in lined ducts with an axial flow of the sound pressure waves. There is need to know the boundary conditions at the walls and at the treatment surfaces (Malmary & Carbonne, 2001).
According to Malmary & Carbonne (2001) the normalized acoustic impedance is given as:
Zt= 1/PoCo x (P/v’n’) …. (1)
where P= acoustic pressure at a point of the surface of the liner, v’ = acoustic velocity at the same point, n’= normal to the surface of the liner, Co=speed of sound in air and ?= air density
However, a part from the layer impedance, there is cavity impedance which must also be factored in hence the total acoustic impedance from the system is given by:
Zt= Z-jcot(KL) …… (2)
where K= acoustic wave number, K=w/co and L= cavity depth
Therefore, critical parameters that will determine the relevance of the model in the practical sense include: the dimensional property of the attenuating medium and the flow characteristics such as mach number, frequency among others which mathematically can be represented as:
Z= z(e,d,?,w,/v/, M)….(3)
Where w= sound pulsation
/v/= amplitude of the normal acoustic velocity
M= Flow Mach number
However, it should be noted that the above model is linearized where the frequency characteristic relates with the acoustic impedance as follows:
Firstly, for a perforated pipe, according to Malmary & Carbonne (2001) the impedance is given as: Z= r+jX …..(4)
Where r= (8vw)0.5/?Co(1+e/d) +1/8?(kd)2 and X= w/?Co[e+8d/3π(1-0.7?0.5) +(8v/w)0.5(1+e/d)]
However, as pointed out earlier, this model is not sufficient in its entirety so to speak; because the real-world acoustic systems often exhibit non-linear behavior hence a further extension to the method is necessary. However, there are other more specific methods that utilize the acoustic impedance phenomenon with their underlying applications as discussed in the next paragraphs
Spatial compounding
More often, acoustic impedance measurements could be used in the generation of the ultrasound images but problems of occlusions may hinder the performance in situations where the material acoustic impedance is high. Unlike the other scenarios, where the mean of the impedances can be used in a straight fashion; this case requires the beam intensity to be increased so as to overcome the material impedances. This is what is termed as spatial compounding. Hence often the material acoustic impedance will have to be known from the standardized models after which the system design will take root. Nevertheless, spatial compounding ensures that the ultrasound imaging is a near excellent result while overcoming the layer impedances during propagation (Malmary & Carbonne , 2001).
References
Dingzeyu Li, David, I, Matusik, W& Changxi Zheng, C. (2016). Acoustic Voxels: Computational Optimization of Modular Acoustic Filters. Available from: https://www.cs.columbia.edu/cg/lego/acoustic-voxels-siggraph-2016-li-et-al.pdf
Malmary, C & Carbonne, S. (2001). Acoustic impedance measurement with grazing flow. Available from: https://perso.univ-lemans.fr/~yauregan/publi/AIAA-2001-2193.pdf
Rienstra, S.W& Hirschberg, A. (2017).An Introduction to Acoustics. Eindhoven University of Technology. Available from: https://www.win.tue.nl/~sjoerdr/papers/boek.pdf
Wachinger, C, Shams, R & Navab, N. (2008). Estimation of Acoustic Impedance from Multiple Ultrasound Images with Application to Spatial Compounding. Available from : https://campar.in.tum.de/pub/wachinger2008impedance/wachinger2008impedance.pdf
Chalmers. (2012). Evaluation of impedance tube methods – A two microphone in-situ method for road surfaces and the three-microphone transfer function method for porous materials. Available from: https://publications.lib.chalmers.se/records/fulltext/178260/178260.pdf
Utsuno, H., Toshimitsu Tanaka., T & Fujikaw., T. (1989). Transfer function method for measuring characteristic impedance and propagation constant of porous materials. Available from: https://spectronics.net/resources/Technical%20Papers/Bulk%20Properties_1.pdf
Yunseon, R. (no year). The Acoustic Impedance Measurement System using two microphones. Available from: https://citeseerx.ist.psu.edu/viewdoc/download?doi=10.1.1.612.6612&rep=rep1&type=pdf
Vorlander, M. (2013). Acoustic Measurements. Available from: file:///C:/Users/Otieno/Downloads/9783540240525-c1.pdf
Pcfarina. (2006). Acoustic Impedance Measurements. Available from: https://pcfarina.eng.unipr.it/Public/Standing-Wave/ebook_6_impedance.pdf
Schultz,T., Cattafesta,L.N & Sheplak, M. (2006). Modal decomposition method for acoustic impedance testing in square ducts. Available from: https://asa.scitation.org/doi/10.1121/1.2360423
Hull, J.A. (1992). A Comparison of Acoustic Impedance Measurement Techniques. Submarine Sonar Department. Available from: https://www.dtic.mil/dtic/tr/fulltext/u2/a255566.pdf
Pcfarina. 2006. Acoustic Impedance Measurements. Available from: https://pcfarina.eng.unipr.it/Public/Standing-Wave/ebook_6_impedance.pdf
Spatial and Frequency Compounding in Application to Attenuation Estimation in Tissue Ziemowit KLIMONDA, Jerzy LITNIEWSKI, Piotr KARWAT, Andrzej NOWICKI Institute of Fundamental Technological Research Polish Academy of Science. Available from: https://www.ippt.pan.pl/Repository/o2659.pdf
Thesis. Chapter 3 -Basic Acoustic Modeling. Available from: https://theses.lib.vt.edu/theses/available/etd-10232000-10320002/unrestricted/Chap3.pdf
Williams, L & Wilkins. 2009. Acoustic Impedance. Walters Kluwer Health. Available from: https://www4.uwsp.edu/physastr/kmenning/Phys115/Link5-09_acoustic_impedance.pdf
Wolkesson, M. 2013. Evaluation of impedance tube methods – A two microphone in-situ method for road surfaces and the three microphone transfer function method for porous materials Masters Thesis in the Masters programme in Sound and Vibration. Chalmer University of Technology. Available from: https://publications.lib.chalmers.se/records/fulltext/178260/178260.pdf
Essay Writing Service Features
Our Experience
No matter how complex your assignment is, we can find the right professional for your specific task. Contact Essay is an essay writing company that hires only the smartest minds to help you with your projects. Our expertise allows us to provide students with high-quality academic writing, editing & proofreading services.
Free Features
Free revision policy
$10Free bibliography & reference
$8Free title page
$8Free formatting
$8How Our Essay Writing Service Works
First, you will need to complete an order form. It's not difficult but, in case there is anything you find not to be clear, you may always call us so that we can guide you through it. On the order form, you will need to include some basic information concerning your order: subject, topic, number of pages, etc. We also encourage our clients to upload any relevant information or sources that will help.
Complete the order form
Once we have all the information and instructions that we need, we select the most suitable writer for your assignment. While everything seems to be clear, the writer, who has complete knowledge of the subject, may need clarification from you. It is at that point that you would receive a call or email from us.
Writer’s assignment
As soon as the writer has finished, it will be delivered both to the website and to your email address so that you will not miss it. If your deadline is close at hand, we will place a call to you to make sure that you receive the paper on time.
Completing the order and download