The purpose of the investigation is to find the aspects impacting the rate cooling. Likewise to reveal that there is a relationship between 2 elements that impact the rate of cooling if there is two factors. Prediction In my experiments I am going to utilize 6 differed sized beakers, I will keep the volume inside the beakers at a constant 50ml. I want to prove that when I alter the size of the beaker, larger, then the cooling would take less time. This will be because more surface area will be exposed.
It is likewise likely that if I increase the volume but keep the very same size beaker the cooling will take longer.
This is since the liquid not exposed to the air will retain its heat for a longer duration of time.? In the very first experiment a lot of heat will be lost because the particles have a big amount of energy.? In the 2nd experiment a fair amount of heat will be lost, at about half the rate of the first experiment.
This is since the particles still have energy but the majority of this energy has been utilized since of lack of heat.? In the third experiment not much heat will be lost. This is since there is not much energy left in the liquid.
Heat will be lost when there is lots of energy, when heat is lost the energy decreases causing the rate of cooling to decrease. I predict that when the temperature of the solution is increased, the speed of the reaction will increase.
This is because the molecules will have more energy; therefore making them move faster. The molecules will then disperse heat evenly. The graphs I plot of my results will show a relationship between temperature and time. I believe that the graph will begin with a steep gradient, as the heat is high but will then begin to level out as the heat decreases. Method Equipment Used:
50cm3 beaker Stopwatch 100cm3 beaker Bunsen burner 250cm3 beaker Tri-Pod 400cm3 beaker Heat proof-mat 800cm3 beaker Thermometer Water Gauze ? To keep an accurate measurement I will use the same thermometer and end the experiment when the liquid reaches 50oC. ? I will measure the time it takes from when the liquid reaches 95oC. ? To keep accurate and constant results I will ask a friend to measure the time while I measure the temperature of the liquid. I will keep the total volume of water at a constant 50cm3. The stopwatch will be started as soon as the liquid reaches 95oC and when the Bunsen burner has been removed.
For this experiment I am going to change the surface area exposed to the surrounding air. I will use six different sized beakers each with a different radius in order to gather enough information to see a pattern if there is one. Results Experiment Number Area of Beaker Cm2 Capacity of Beaker Time (Minutes) Average Time (Minutes) ____10000____ Average Time (to 1 decimal place) .
Experiment Number Volume Cm3 Temperature oC Average Temperature oC ____1000____ Average Temperature oC (1 decimal place)- Conclusion When looking at the graph below it is quite obvious to see that the speed of the cooling decreases as the surface area is decreases. It is therefore easy to predict that the speed of the reaction is directly proportional to the surface area.
By taking results from the two experiments you cane see that as the surface area increases then the rate of cooling also increases. Therefore it is clear through my results, that rate of cooling and surface area, are directly proportional to each other when using water. For example: when the surface area increases the rate of cooling decreases and when the surface area decreases the rate of cooling increases. Evaluation Through my experiment I attempted to take as much precaution as possible to make the test a fair and accurate test.
However my results and patterns in my graphs show that not all the tests were accurate, as some points do not fit in with the obvious pattern. One of main problem was that I had to estimate how much water to put into the beaker before heating; this was not easy as the water evaporated off and on several occasions we were left with not enough liquid in the beaker. To help with this problem I could have heated more than enough water and the poured the correct amount into another beaker, however, a lot of heat my have been lost in this way.
A waterproof container may have also been helpful as it was have meant that no water to could be lost through evaporation. Another factor affecting my results could have been the humidity within the room on different days. This would have effected the cooling slightly but enough to make a difference. The slight heat would have made the molecules slightly more energetic but not enough to disrupt the experiment I don’t believe. An alternative may have been to use a sealed off laboratory or to do all the experiments within the same climate
Overall I was delighted with how the experiments ran and how my results were gathered and turned out. To perform the experiment again I would need to use many mechanical aids as possible so that I could exclude human error wherever needed. Thus making more accurate and fairer results. Show preview only The above preview is unformatted text This student written piece of work is one of many that can be found in our GCSE Patterns of Behaviour section.
Remember! This is just a sample.
You can get a custom paper by one of our expert writers.
Get your custom essay
Helping students since 2015
Essay Writing Service Features
Our Experience
No matter how complex your assignment is, we can find the right professional for your specific task. Contact Essay is an essay writing company that hires only the smartest minds to help you with your projects. Our expertise allows us to provide students with high-quality academic writing, editing & proofreading services.
Free Features
Free revision policy
$10Free bibliography & reference
$8Free title page
$8Free formatting
$8How Our Essay Writing Service Works
First, you will need to complete an order form. It's not difficult but, in case there is anything you find not to be clear, you may always call us so that we can guide you through it. On the order form, you will need to include some basic information concerning your order: subject, topic, number of pages, etc. We also encourage our clients to upload any relevant information or sources that will help.
Complete the order form
Once we have all the information and instructions that we need, we select the most suitable writer for your assignment. While everything seems to be clear, the writer, who has complete knowledge of the subject, may need clarification from you. It is at that point that you would receive a call or email from us.
Writer’s assignment
As soon as the writer has finished, it will be delivered both to the website and to your email address so that you will not miss it. If your deadline is close at hand, we will place a call to you to make sure that you receive the paper on time.
Completing the order and download