HOOKE’S LAW: Hooke’s lawof elasticity is an approximation that states that the extension of a spring is in direct proportion with the load added to it as long as this load does not exceed the elastic limit. Materials for which Hooke’s law is a useful approximation are known as linear elasticor “Hookean” materials.
If a metal is lightly stressed, a temporary deformation permitted by an elastic displacement of atoms in space takes place. Removal of stress results in a gradual return of metal to its original shape.
Mathematically, Hooke’s law states that
Where,
xis the displacement of the end of the spring from its equilibrium position;
Fis the restoring force exerted by the material; and
kis theforce constant(orspring constant).
DIAGRAMATICALLY:-
When no weight is applied to the spring, the strain is zero,
And, we can measure its length,.
and when we apply a force F to the spring It stretches
And it extends length,x, that is, the strain, caused by the stress is
F = mg.
Also,
In terms of mechanics hooks state that:-
“For an elastic material stress applied on a body is directly proportional to the strain produced”
That is, σ α e
Or σ = E e
Where,
σ is the stress applied
e is the strain developed
E is the YOUNGS MODULUS OF ELASTICITY
Now
STRESS it is the force causing the deformation.
It is measured in units of force per unit area of cross-section (N.m-2) denoted byσ(“sigma”).
That is σ= F/A
Units of stress are Pascal…
Strain is the deformation that takes place in the body.
It is the ratio of the increase in length,DLto the original length (L),
Represented by symbolε(“epsilon”) or e.
That is
e=DL/L
It is dimensionless.
And according to hook’s law: σ = E e
Or, E = σ/e
Putting values of stress and strain in above equation we get:-
E = FÃ-L/AÃ-DL
Young’s modulus of elasticity (E) is defined as the ratio of unit stress to unit strain .
GENERALIZED HOOK’S LAW:
The generalized Hooke’s Law can be used to predict the deformations caused in a given material by an arbitrary combination of stresses.
The linear relationship between stress and strain applies for
The generalized Hooke’s Law also reveals that strain can exist without stress. For example, if the member is experiencing a load in the y-direction (which in turn causes a stress in the y-direction), the Hooke’s Law shows that strain in the x-direction does not equal to zero. This is because as material is being pulled outward by the y-plane, the material in the x-plane moves inward to fill in the space once occupied, just like an elastic band becomes thinner as you try to pull it apart. In this situation, the x-plane does not have any external force acting on them but they experience a change in length. Therefore, it is valid to say that strain exist without stress in the x-plane.
STRESS-STRAIN CURVE:-
Thestress-straincurve is a graphical representation of the relationship betweenstress, derived from measuring the load applied on the sample, andstrain, derived from measuring thedeformationof the sample, i.e. elongation, compression, or distortion. The nature of the curve varies from material to material.
ELASTIC LIMIT:
The elastic limit is where the graph departs from a straight line. If we go past it, the spring won’t go back to its original length. When we remove the force, we’re left with apermanent extension.
Below the elastic limit, we say that the spring is showing “elastic behaviour”: the extension is proportional to the force, and it’ll go back to it’s original length when we remove the force.
Beyond the elastic limit, we say that it shows “plastic behaviour”. This means that when a force is applied to deform the shape, it stays deformed when the force is removed.
YIELD POINT:
Theyield strengthoryield pointof a materialis defined in engineering and material science as the stress at which a material begins to deform plastically . Prior to the yield point the material will deform elastically and will return to its original shape when the applied stress is removed. Once the yield point is passed some fraction of the deformation will be permanent and non-reversible.
True elastic limit:
The lowest stress at whichdislocationsmove. This definition is rarely used, since dislocations move at very low stresses, and detecting such movement is very difficult.
Proportionality limit:
Up to this amount of stress, stress is proportional to strain hookes law so the stress-strain graph is a straight line, and the gradient will be equal to the elastic modulus of the material.
Elastic limit (yield strength):
Beyond the elastic limit, permanent deformation will occur. The lowest stress at which permanent deformation can be measured. This requires a manual load-unload procedure, and the accuracy is critically dependent on equipment and operator skill. For elastomers such as rubber the elastic limit is much larger than the proportionality limit. Also, precise strain measurements have shown that plastic strain begins at low stresses.
Get Help With Your Essay
If you need assistance with writing your essay, our professional essay writing service is here to help!
Essay Writing Service
Offset yield point (proof stress)
This is the most widely used strength measure of metals, and is found from the stress-strain curve. A plastic strain of 0.2% is usually used to define the offset yield stress, although other values may be used depending on the material and the application. The offset value is given as a subscript, e.g., Rp0.2=310 MPa. In some materials there is essentially no linear region and so a certain value of strain is defined instead. Although somewhat arbitrary, this method does allow for a consistent comparison of materials.
Upper yield point and lower yield point
Some metals, such as mild steel reach an upper yield point before dropping rapidly to a lower yield point. The material response is linear up until the upper yield point, but the lower yield point is used in structural engineering as a conservative value. If a metal is only stressed to the upper yield point, and beyond rubber band can develop.
NUMERICALS:-
Q1) When a 13.2-kg mass is placed on top of a vertical spring, the spring compresses 5.93 cm. Find the force constant of the spring.
Solution: Mass = 13.2 kg
Weight = 13.2Ã-9.8
= 129
Compression (x) = 5.93 = 0.0593 m
From Hooke’s Law: F = kx
The force on the spring is the weight of the object, i.e.(F) = 129 N
Putting values of force and compression in above equation;
129 = (0.0593) Ã- k
Or,
k = 2181 N/m Answer
Q2) A 3340 N ball is supported vertically by a 2m diameter steel cable assuming cable has a length of 10m, determine stress and strain in the cable. Young’s modulus for steel is 200N/sq.m.
Solution:
Force (F) = 3340N
Diameter = 2m
Radius (r) = 1m
Length of cable = 10m
Young’s modulus (E) = 200N/sq.m
Now we know,
Stress (σ) = F/A
Area =
= 3.14Ã-1Ã-1 = 3.14
So, σ = 3340/3.14
σ = 1063.69N/m.sq
Also, strain (e) = σ/E
Putting values…
e = 1063.69/200
e =5.3184
Answer
Q3) If a spring has a spring constant of 400 N/m, how much work is required to compress the spring 25.0 m from its undisturbed position?
Solution: spring constant (K) = 400 N/m
compression (x) = 25m
we know, force required for compression:-
F = kx
i.e. F = 400×25 = 10000N
and work done = force x compression
w = F x X
w = 10000 x 25
w = 25,000 Joules Answer
Q4) On a of steel rod of length 15m and diameter 6m a force of 60N is applied. Calculate the extension and new length of the rod. Young’s modulus of steel is 250N/m.sq.
Solution: :
Force (F) = 60 N
Diameter = 6m
So, Radius (r) = 3m
Length (L) = 15 m
Young’s modulus (E) = 250N/m.sq.
Now,
Area (A)
A = 3.14 x 3 x 3
A = 28.26 sq.m
Also, , E = FÃ-L/AÃ-DL
Or, DL = FÃ-L/AÃ-E
DL = 60Ã-15/28.26Ã-250
DL = 0.127m
SO, new length = 15+0.127
L’ = 15.127m ANSWER
REFERENCES:-
1) www.physicsworld.com
2) www.wikipedia.org
3) www.123iitjee.com
4) www.physicsforum.com
5) www.matter.org.content/HookesLaw
6) www.webphysics.davidson.edu/hook
7) www.scienceworld.com
Essay Writing Service Features
Our Experience
No matter how complex your assignment is, we can find the right professional for your specific task. Contact Essay is an essay writing company that hires only the smartest minds to help you with your projects. Our expertise allows us to provide students with high-quality academic writing, editing & proofreading services.
Free Features
Free revision policy
$10Free bibliography & reference
$8Free title page
$8Free formatting
$8How Our Essay Writing Service Works
First, you will need to complete an order form. It's not difficult but, in case there is anything you find not to be clear, you may always call us so that we can guide you through it. On the order form, you will need to include some basic information concerning your order: subject, topic, number of pages, etc. We also encourage our clients to upload any relevant information or sources that will help.
Complete the order form
Once we have all the information and instructions that we need, we select the most suitable writer for your assignment. While everything seems to be clear, the writer, who has complete knowledge of the subject, may need clarification from you. It is at that point that you would receive a call or email from us.
Writer’s assignment
As soon as the writer has finished, it will be delivered both to the website and to your email address so that you will not miss it. If your deadline is close at hand, we will place a call to you to make sure that you receive the paper on time.
Completing the order and download
