1.
Wein Bridge Osciator:
Wien bridge oscillator is one type of oscillator. The oscillator has a high resonant frequency, low distortion. The oscillator has no input (Lerner, 2016) .The Wien bridge oscillator was developed by Wien (ElProCus – Electronic Projects for Engineering Students, 2018). It is used to measure the impedance value. It has four resistors and two capacitors.
Figure 1 schematic of weinbridge oscillator
When R1 =R2=R,AND C1=C¬2=C
The stable condition was given below
Given frequency is f =57 KHZ
By substituting the frequency value to the above equation
R=1K?
C=2.79nF
2.
Operational Amplifier:
An operational amplifier is a voltage amplifier.it produces output that is equal to the difference of its inputs(COMPARATIVE ANALYSIS OF TWO STAGE OPERATIONAL AMPLIFER, 2015). Operational amplifiers often called as opamp . The opamp is one type of differential amplifier. Opamp has two inputs namely inverting and non-inverting terminals.
Differential Amplifier:
The differential amplifier is electronic amplifier.it is used to amplify the difference between the input voltages and reduces the common voltages.it has two modes of operations as common mode and differential mode. For good differential amplifier differential mode gain should be high (Guo, 2017).
Common Mode Rejection Ratio:
CMRR of a differential amplifier is very important characteristic of a differential amplifier that is given by,
CMRR=Ad/Ac
CMRR value of differential amplifier should be high.
The ideal opamp is given by
Vout = A (Vin+ – Vin–)
Where, A is gain of the amplifier
Vin+ is non inverting terminal input voltage
Vin– is inverting terminal input voltage
From given figure
When making V2 short-circuited Non inverting output is given by,
Vout+ = V1(R2/(R1+R2)).(1+(R4/R3)
Similarly, when V1 is short-circuited inverting output is given by
Vout– = -V2(R4/R3)
The total output of a Differential amplifier is
Vout = -V2(R4/R3) + V1R2/(R1+R2).(1+(R4/R3)
When R2 = R4 and R1 = R3.the output will be reduced to
Vout = R2/R1(V2-V1)
Reasons:
Because of these reasons Instrumentation amplifier requires the op amps. Two additional opamps are used to reduce low resistance. The output of these opamps is given to the second stage differential amplifier.
1.
Here the VHDL code for the given problem was developed and given below. The given state machine starts with SA as starting state and ends with the SC state(COHEN, 2013). Between the starting state as well as ending state the state SB was situated. So here totally there are three nodes. Each node capable of processing the input as well as output (Ece-research.unm.edu, 2018). The direction of the transformation depends upon the input statement given by the user. In this problem, if the state SB has the odd number the x value becomes 0, If the SB value may be even the value of x will become one. For the above constraints, the below code was developed. We can able to simulate this code by using the “Xilink SE”. Here the code was attached (Ashenden, 2011).
“Jonathan Turner” carried out the research on the VHDL design and simulation. From his research, he found the various advantages as well as disadvantages of the various VHDL tools. The advantages of VHDL tools are, speed up the computation process, improve the flexibility of the design, to minimize the cost of the simulation, and reduce the wastages of the testing. These are the positive elements of the VHDL design and simulation according to the author. And he also noticed some of the drawbacks of the VHDL simulation process. And they are Lower accuracy, because the lower no of constraints, cost of the simulation tool, and the computation process were highly complicated. These are the results of his research. These are considered for this research work.
“Valentina Stoyanova Kukenska” carried out the research on the VHDL design of structural model and behavior model. From his research, he found the various advantages and disadvantages in the structural and behavior model. The structural model has two stages, top-down designing and uptown designing. By the top down simulation, we can able to check the error, so it has the higher processing speed. The up-down process consumes the higher time for calculation than the Top down method. But it gives the more details about the process. And also he noticed some drawbacks in structural model and behavior model. The structural model was limited to sequential circuits only. It is a step by step process the time delay will be occurring in this model. These are the results of his research .these are considered for his research work.
“Muzakkir Mas’ud Adamu” carried out the research of VHDL design and simulation. From his research, he founded the various advantage as well as disadvantages of the various VHDL tools. Here these are considered for this resource. The advantages of VHDL design techniques are to design the digital design flow for the low power embedded products. In a computer application, the usage of flexibility can change the reducing the cost of system software. The circuits are design and manufacturing for the integrated forms. The device speed was high and its range was GHz to THz.The transmission of data to be encrypted. The disadvantages are the IC cannot be easily portable. The cost of the tool will be high. The real-time signal processing will be no guarantee. The approximation errors will occur. It is expensive and complex.
Based on the study carried out by Aziza I. Hussein et al. summarized the following advantages and disadvantages. The highly complex design is easily designed as well as simulated by using those kinds of simulation software. Also, it provides the good and reliable results for the system. Highly complex codes are easily simulated by this software. According to this author, these points are the advantages of the VHDL design and simulation software. But this software has some disadvantages also. For the single-use, this software was too costly. Also, it has some limitations in the digital design developing stage.
Rajesh Kumar Gupta carried the research and he found the following advantages and disadvantages. Here we can able to improve the overall effectiveness of the embedded system design process. Because this method reduces the time required to design as well as check the system. And also the overall amount spent on the prototyping and testing was reduced. All the simulations were done by the computer so the accuracy was higher than the manual calculation and testing process. We can able to optimize the shape, size power requirements. By this simulation we can able reduce the complexity involves in the gate array designing. The above-described points are considered as the advantages of using the VHDL design and simulation for developing the digital systems. But it has some disadvantages also, for example, the operating procedure for those kinds of software tools are highly complex in nature. So it needs highly trained employees to do those jobs. The initial price of those software tools is also high. That also requires high-level system configurations.
References
Ashenden, P. (2011). The designer’s guide to VHDL. Amsterdam: Morgan Kaufmann Publishers.
COHEN, B. (2013). Vhdl Coding Styles And Methodologies. [S.l.]: Springer-Verlag New York.
COmparative Analysis Of Two Stage Operational Amplifer. (2015). International Journal of Advance Engineering and Research Development, 2(04).
Ece-research.unm.edu. (2018). VHDL Introduction. [online] Available at: https://ece-research.unm.edu/jimp/vlsi/slides/vhdl.html [Accessed 30 Jun. 2018].
ElProCus – Electronic Projects for Engineering Students. (2018). Wien Bridge Oscillator Circuit Theory and Working – Elprocus. [online] Available at: https://www.elprocus.com/wien-bridge-oscillator-circuit-working/ [Accessed 30 Jun. 2018].
Guo, J. (2017). A low-voltage sense amplifier with two-stage operational amplifier clamping for flash memory. Journal of Semiconductors, 38(4), p.045001.
Lerner, L. (2016). The dynamics of a stabilised Wien bridge oscillator. European Journal of Physics, 37(6), p.065807.
Watson, J. and Castro, G. (2012). An Ultra-Low Noise Instrumentation Amplifer Designed for High Temperature Applications. Additional Conferences (Device Packaging, HiTEC, HiTEN, & CICMT), 2012(HITEC), pp.000082-000086.
Essay Writing Service Features
Our Experience
No matter how complex your assignment is, we can find the right professional for your specific task. Contact Essay is an essay writing company that hires only the smartest minds to help you with your projects. Our expertise allows us to provide students with high-quality academic writing, editing & proofreading services.
Free Features
Free revision policy
$10Free bibliography & reference
$8Free title page
$8Free formatting
$8How Our Essay Writing Service Works
First, you will need to complete an order form. It's not difficult but, in case there is anything you find not to be clear, you may always call us so that we can guide you through it. On the order form, you will need to include some basic information concerning your order: subject, topic, number of pages, etc. We also encourage our clients to upload any relevant information or sources that will help.
Complete the order form
Once we have all the information and instructions that we need, we select the most suitable writer for your assignment. While everything seems to be clear, the writer, who has complete knowledge of the subject, may need clarification from you. It is at that point that you would receive a call or email from us.
Writer’s assignment
As soon as the writer has finished, it will be delivered both to the website and to your email address so that you will not miss it. If your deadline is close at hand, we will place a call to you to make sure that you receive the paper on time.
Completing the order and download