Fluoride is excessively available in ground water is very common in India. To knowing the adverse effects of fluoride in water many adsorbents using time to time but due to many side effects of defluoridation we need a perfect method for this. In this research work we have been applied a comparative study of two different cheap adsorbent .The using adsorbents are Fly ash and marble powder. Here used fly ash, generated from Chula. And pieces of marble collected from construction area and crushed for use in the laboratory.
In this research work Ash, Marble powder is mixed with fluoridated water. After the analysis we found both of the adsorbents removes fluoride from drinking water but the results were found from fly ash is better than from marble powder.
KEYWORDS: Adsorption, Defluoridation, Fluoride, Fly Ash, Marble Powder PH.
Fluoride is a positively charged ion like calcium (Ca++). It is important for our bones and teeth but having highest amount of calcium in the body attracts the maximum amount of fluoride.
It is deposited in form of Calcium Fluorapatite crystals in the body. Excess of fluoride above 1.5 mg/L may cause to serious manifestations, which are described below:-
Common defluoridation methods of drinking water:
Removal of excess fluoride from drinking water called defluoridation.
The process of defluoridation can use by following methods:-
Developed countries are using source treatment method (i). Defluoridation is a technical treatment method under the supervision of skilled persons here cost is a limiting factor. But in the less developed countries the same approach may not be feasible, especially in rural areas, where settlements are scattered. Treatment at the point of use (ii) has several advantages over treatment at community level. Treatment may only be possible at a decentralized level, for example at the community, village or household level. Costs are lower, as defluoridation can be restricted to the demand for cooking and drinking – usually less than 25% of the total water demand. Chemical treatment of the entire water demand would lead to production of large volumes of sludge, which requires a safe disposal.
It has been found that the defluoridation methods of drinking water are not sufficient when initial concentration of fluoride in the water is very high and the pH of the untreated water is alkaline. Moreover, different degrees of hardness of water require different concentrations of alum.
Various limitations are found when we use of point of use treatment method like reliability of the treatment units has to be assured, and that all users should be motivated to use only the treated water for drinking and cooking at the condition is untreated water is also available in the house
National Environment Engineering Research Institute in Nagpur, India (NEERI) has evolved an economical and simple method of defluoridation, which is referred to as the Nalgonda technique. UNICEF has worked closely with the Government and other partners in defluoridation programmes in India, where excessive fluoride has been known for many years to exist in groundwater. In the 1980s, UNICEF supported the Government’s Technology Mission in the effort to identify and address the fluoride problem: the Government subsequently launched a massive programme, still under way, to provide fluoride-safe water in all the areas affected. The Nalgonda technique has been repeatedly proven to be an economical and effective household defluoridation technique. (Lela Iyenger, March 2005, UNICEF, New Delhi) In this technique, fluoride is precipitated using 500 mg/L of alum and 30 mg/L of lime.
For removal of fluoride from drinking water three mechanisms can be apply:
Addition of chemicals or Chemical additive methods
These methods involve the addition of soluble chemicals to the water. Fluoride is removed either by precipitation, co-precipitation, or adsorption onto the formed precipitate. Chemicals include lime used alone or with magnesium or aluminum salts along with coagulant aids. Treatment with lime and magnesium makes the water unsuitable for drinking because of the high pH after treatment. The use of alum and a small amount of lime has been extensively studied for defluoridation of drinking water.
The method popularly known as the Nalgonda technique (RENDWM, 1993), is one of example named after the town in India where it was first used at water works level. It involves adding lime (5% of alum), bleaching powder (optional) and alum (Al2(SO4)3.18H2O) in sequence to the water, followed by coagulation, sedimentation and filtration (L.Iyenger,2005). A much larger dose of alum is required for fluoride removal (150 mg/mg F-), compared with the doses used in routine water treatment. As hydrolysis of alum to aluminum hydroxide releases H+ ions, lime is added to maintain the neutral pH in the treated water. Excess lime is used to hasten sludge settling. The dose of alum and lime to be added in raw water with different fluoride concentrations and alkalinity levels (G.Karthikeyan and A. Shunmuga Sundarraj, 1999).
The reaction occurs through the following equations:
2 Al2 (SO4)3.18H2O + NaF + 9Na2CO3 ? [5Al (OH) 3 Al (OH) 2F] + 9Na2SO4+NaHCO3 + 8 CO2 + 45 H2O
3 Al2 (SO4)3.18H2O + NaF +17NaHCO3 ? [5Al (OH) 3 Al (OH) 2F] + 9Na2SO4+ 17 CO2 + 18 H2O
The Nalgonda technique has been successfully used at both individual and community levels in India and other developing countries like China and Tanzania. Domestic defluoridation units are designed for the treatment of 40 liters of water. Whereas the fill-and-draw defluoridation plant can be used for small communities. Alum treatment is seldom used for defluoridation of drinking water in developed countries.
Contact precipitation is a technique in which fluoride is removed from water through the addition of calcium and phosphate compounds. The presence of a saturated bone charcoal medium acts as a catalyst for the precipitation of fluoride either as CaF2, and/or fluorapatite. Tests at community level in Tanzania have shown promising results of high efficiency. Reliability, good water quality and low cost are reported advantages of this method (Chilton, et al., 1999).
In the adsorption method, raw water is passed through a bed containing defluoridating material. The material retains fluoride either by physical, chemical or ion exchange mechanisms. The adsorbent gets saturated after a period of operation and requires regeneration.
A wide range of materials has been tried for fluoride uptake. Bauxite, magnetite, kaolinite, serpentine, various types of clays and red mud are some of the naturally occurring materials studied. The general mechanism of fluoride uptake by these materials is the exchange of metal lattice hydroxyl or other anionic groups with fluoride.
Fluoride uptake capacity can be increased by certain pre-treatments like acid washing, calcinations, etc. None of the mentioned materials generally exhibits high fluoride uptake capacities.
Processed materials like activated alumina, activated carbon, bone char, defluoron-2(sulphonated coal) used for defluoridation of drinking water .And synthetic materials like ion exchange resins also have been extensively evaluated for defluoridation. Among these materials, bone char, activated alumina and calcined clays have been successfully used in the field; (Cummins, 1985, Susannae Rajchagool and Chaiyan Rajchagool, 1997, and Priyanta and Padamasiri, 1996).
Area of work: Sitapura Industrial area, Tehsil Sanganer, District Jaipur (Rajasthan).
Sitapura Industrial Area is located 6.0 Km from Jaipur Air port along NH-12. This area is known as EPIP (Export Promotion Industrial Park). Jaipur city is 18 km from EPIP. The area is around 365.00 acres. The water quality is potable in this area. Water availability by tube wells. The Depth of tube wells are approximate 30m. Average discharge of water is 2,000 gallons per hour. The prominent industries of in this area are chemical and automobile industries. Thousands of residential flats are available in and around area. ITI, Polytechnics, Engineering Institutes, Medical Institutes and Hospitals, Management, IT and Architectural colleges, Fashion Designing Institutes .shopping complex etc. are located in this area.
Aim of work: Due to proved health hazards, complicated procedure and expenditure, many popular defluoridation process like – Nalgonda, Activated alumina etc. methods are in the phase out process therefore the aim of the present research work is to find out a best defluoridation method which is easy to use by illiterate villagers, requires minimal expenditure, involvement of less technical personal and effective methods for fluoride removal from drinking water so that these methods can be apply easily everywhere.
Importance of defluoridation: Due to various health impacts of fluoride on human beings the treatment of fluoride is necessary.
Defluoridation methods used in research work:
In view of the demerits of some defluoridation methods, in the present research work we have tried to use some cheap, effective and easily available good adsorbent of fluoride for the purpose of defluoridation. These simple methods can be applied easily under all circumstances.
Method A: Defluoridation by Fly Ash (based on adsorption process): -The fly ash is an effective adsorbent of fluoride .In this method we have used fly ash, generate from Chula. The 100 gm ash was mixed with 1 liter water having fluoride. Stir 5 to 10 minutes then keep it for settle at least for 2 hr. After 2 hour this solution was filtered (G-3 crucible)
Method B: Defluoridation by Marble Powder (based on chemical treatment process): – In chemical treatment processes, lime treatment is one of them. In this method, we collected marble stone and crushed into marble powder. Then it was used for removal of fluoride in place of lime.100 gm of marble powder was mixed with1 liter water having fluoride. Stir 5 to 10 minutes then keep it for settle at least for 2 hr. After 2 hour this solution was filtered (G-3 crucible)
Important fluorides bearing mineral are fluoride apatite, amphiboles and micas. The concentration in ground water is limited due to the low solubility of most fluorides, but in some areas the concentration reaches above 5ppm.
For the determination of fluoride we use ions electrode method.
A potential is established by the presence of fluoride ions across the crystal which is measured by an ion meter. The ions selective electrode is a fluoride sensitive electrode of the solid state type which consisting of a lanthanum fluoride crystal. It can be use in forms of a cell in the combination with a reference electrode, called calomel electrode. The crystal contacts the sample solution at the one face and an internal reference solution at the other.
As per the WHO (World Health Organization), permissible limit of Fluoride in drinking water should be 1.5 mg/l.
To address the fluoridation problem in and around Sitapura Industrial Area, Jaipur 10 sample collection sites were undertaken for the present study. The study was conducted in three phases based on seasons and water usage. Two methods were employed on the samples for defluoridation in each phase. Different physical and chemical parameters along with Nitrate, Fluoride and Heavy metals were analyzed.
Physical and chemical analysis like PH, Hardness, Chloride, Total Dissolve Solid (TDS), and Alkalinity has been done in the laboratory of JaganNath University, Chaksu while some parameters like Fluoride, Nitrate and Heavy metals were analyzed by Team Test Lab Sitapura, Jaipur.
In phase I, all samples were collected after rainy season. During the analysis of parameters we found that sample No.6 which is collected from JNIT College has maximum fluoride concentration (2.84mg/l) and minimum fluoride concentration found in sample No.3 which is collected from Ratan Textile (1.18mg/l). We also found the fluoride concentration exceeds from the permissible limit in maximum samples collected from the study areas.
When sample No. 6 was defluoridized with fly ash, the concentration of fluoride dropped from 2.84 to 0.88 mg/l. When we remove the fluoride by using fly ash method the concentration of fluoride goes down below the permissible limit. On using marble powder the amount of fluoride decreased to 2.35 mg/l.
In II and III phase, again we found almost same result for all the samples as in phase I.
We can see the variations of fluoride concentration in all samples of all phases before and after defluoridation methods ( figure 2).
The variations in percentage (%) of Fluoride content by different defluoridation methods in all samples are given in the Table 4. It has been observed from the percentage (%) variations, that fly ash can remove fluoride from drinking water more effectively than marble.
The aim of our study was to find out the best suitable defluoridation methods which could be employed easily and effectively.
When samples were defluoridized with fly ash the concentration of fluoride dropped drastically in all samples. But due to the chemical nature of fly ash other physico-chemical parameters showed an increase. All other parameters like TDS, Alkalinity, Hardness, Nitrate, and Chloride were controlled without hindering the ability of fly ash to defluoridize the water. No additional traces of heavy metals were detected in the samples after treatment with treated fly ash.
Marble was found to be not much effectively in removal of fluoride comparative to fly ash.
I feel so happy when it comes to acknowledgements after the task is accomplished. I am very thankful to all of those who directly or indirectly helped me in this endeavor. I want to share my deep sense of gratitude to Mr. Deepak Gupta, Chairman, Jagannath University for providing favorable environment for research work and Sincere thanks to Vice Chancellor of Jagannath University for moral support. I express my gratitude and thanks to good advice, support of my supervisor, Dr. Shikha Modi. She has been supported for research work. My Sincere thanks are to members of Team Test Laboratory for giving the results of analysis timely.
Essay Writing Service Features
Our Experience
No matter how complex your assignment is, we can find the right professional for your specific task. Contact Essay is an essay writing company that hires only the smartest minds to help you with your projects. Our expertise allows us to provide students with high-quality academic writing, editing & proofreading services.Free Features
Free revision policy
$10Free bibliography & reference
$8Free title page
$8Free formatting
$8How Our Essay Writing Service Works
First, you will need to complete an order form. It's not difficult but, in case there is anything you find not to be clear, you may always call us so that we can guide you through it. On the order form, you will need to include some basic information concerning your order: subject, topic, number of pages, etc. We also encourage our clients to upload any relevant information or sources that will help.
Complete the order formOnce we have all the information and instructions that we need, we select the most suitable writer for your assignment. While everything seems to be clear, the writer, who has complete knowledge of the subject, may need clarification from you. It is at that point that you would receive a call or email from us.
Writer’s assignmentAs soon as the writer has finished, it will be delivered both to the website and to your email address so that you will not miss it. If your deadline is close at hand, we will place a call to you to make sure that you receive the paper on time.
Completing the order and download