BACKGROUND
Electricity is a form of energy that can be carried by wires and is used for heating and lighting, and to provide power for machines (Collins Dictionary, 2020). In this experiment the electricity was sourced from a power pack which is a transformer used for converting an alternating current (from the mains) to a direct current at a different (usually lower) voltage.
(https://www.electronics-notes.com/articles/equipment-items-gadgets/powerbank/what-is-a-powerbank-battery-store.php).
In this experiment, to conduct the electric flow and current, a conductor was used in an attempt to limit the resistance which is the hindrance to the flow of electrons in material (Electronic Notes, 2020). This was achieved using a resistor which is an electrical component that regulates or limits the flow of electrical current in an electronic circuit. If a specific voltage is required for an active device, for example, a transistor, a resistor can be used (Rouse, 2014).
Electrons travel in zigzag patterns through wires or other external circuits which results in a collision between the electrons and the ions in the conductor, and this process is known as resistance.
George Ohm observed that the difference of a circuit directly relates to the current flowing throughout a circuit, and that a circuit sometimes resists the flow of electricity. Ohm created a rule for working out resistance, shown in the image below:
Resistance is an important element that has been utilised in many forms of technology to perform useful functions, and this experiment looked at how it could be controlled. There are four factors of a wire that impact on the resistance of a wire; material, temperature, diameter and length. This experiment focussed specifically on the last factor – length – to investigate how much the length of a wire effected its electrical resistance, using a range of wire lengths to test with.
AIM
To practically examine the relationship between voltage, current and resistance.
HYPOTHESIS
It was predicted that that the length of the wire would determine the level of resistance (i.e., the longer the wire, the larger the resistance). This is due to the free electrons in the wire bumping into more atoms, making it more difficult for electricity to flow. According to this theory, the graph shows a positive correlation.
VARIABLES
There were a number of variables that could be altered in this experiment; these are known as independent variables. For this experiment the only independent variable was the length of the wire. The controlled variable was the powerpack as the voltage through the wire was controlled. Resistance was the dependent variable in this experiment.
To maintain accuracy a record of the voltage and the current was taken three times every 20cm and the average reading recorded. This served to void any anomalous results and eliminate the chance of false readings. The powerpack was switched off in between each reading to ensure that the wire did not heat up too much.
Power pack- controlled variable
Length- Independent
Resistance- Dependent
MATERIALS
Power pack
Leads with alligator clips
1.1m Nichrome wire (Resistor)
Voltmeter
Light bulbs
Ammeter
Switch
Heatproof mat
10, 15 or 56- ohm resistor
1m ruler
Electrical tape
METHOD
Collected materials
Set up the ruler by taping a wire along it
Connected the wires to the Voltmeter, Ammeter and Power pack
Tested the current and voltage by moving the wires with alligator clips down the wire – tested at 100cm, 80cm, 60cm, 40cm and 20cm
Measured each 20cm x 3 times and turned the power on and off between each trial
Recorded results in table (Figure 3)
Figure 1: Apparatus
SAFETY MEASURES
RISK
PRECAUTION
Electrocution
Ensuring all wires are connected properly
Turning off powerpack in between experiments
Injury to Feet from Falling Objects
Hair Catching on Fire From Sparks
Burns to Eyes
Burns to Hands
Turning powerpack off between experiments to ensure the wires don’t get too hot
RESULTS
The results in the graph below (Figure 2) represent a nearly straight line, indicating a strong positive correlation between length and resistance, which was consistent with the prediction.
Figure 2:
Figure 3:
Results
Length of Nichrome Wire (cm)
Trial results for voltage (V)
Average Results for Voltage (V)
Trial results for current (A)
Average results for current (A)
Resistance (Ohms)
Trial 1
Trial 2
Trial 3
Trial 1
Trial 2
Trial 3
100
1.3
1.3
1.3
1.3
0.11
0.12
0.12
0.12
10.83
80
1.3
1.5
1.5
1.43
0.14
0.14
0.14
0.14
10.21
60
1.5
1.2
1.25
1.32
0.17
0.18
0.18
0.18
7.3
40
1.1
1.1
1.1
1.1
0.24
0.24
0.24
0.24
4.58
20
0.7
0.7
0.7
0.7
0.36
0.37
0.36
0.36
1.94
DISCUSSION
The results showed that as the length of the wire increased, so did the resistance. Furthermore, it suggested that if the length of the wire was doubled, resistance was roughly doubled also e.g. when the length of the wire was 20cm the resistance was 1.94 ohms; when the length of the wire was 40cm the resistance was 4.58 ohms, which is roughly double.
The apparatus used was suitable, however, increasing the number of data readings to achieve more reliable results may have been beneficial, perhaps by increasing the length of the wire by 10cm each time, instead of by 20cm.
Gradient – m= rise/run
= (y2 – y1) / (x2 – x1)
= (10. 21- 7.3) / (80 – 60)
= 2.91/20
=0.15
Evaluation
Overall, the results were consistent with the predictions. There was one reading that veered away from the straight line, but all others were consistent with the general trend. A kink in the wire could have led to this inconsistent reading as it would have prevented a particular part of the wire remaining constant, therefore skewing the result.
The range of results were substantial enough to draw a valid conclusion about how the length of the wire affected the resistance. Figure 2 represents this conclusion.
It is reasonable to predict that the pattern would continue beyond the range of values that were used. Having said that, without specialist equipment the results could potentially be distorted due to the wire overheating and classroom environment not being suitable to increase the length of the wire due to safety concerns and space constraints.
CONCLUSION
The graph in Figure 2 represents an increasing linear trend-line with the mathematical function of Y = 6.9065X + 21.137, showing a positive correlation as seen in the line that goes above and to the right, indicating positive values, as well as the gradient that displays a positive value.
The steady incline proves that when the length of a wire is increased, the resistance responds with an increase also of approximately 3 Ω. This information is consistent with the data provided in Figure 3.
The length of the wires (independent variable) ranged from 20cm to 100cm with increments of 20cm between each trial, while the resistance (dependent variable) data ranged from 1.94 Ω at its lowest to 10.38 Ω at its highest measure. This data is best understood using a line graph (Figure 2).
The pattern shown on the graph supports the hypothesis of the experiment, proving that, when the length of the wire was increased, the resistance measured increased accordingly, resulting in a positive gradient. This was proven and supported by the trend-line in the graph which depicts a positive correlation in the increase in resistance in the same measure as the independent variable increases. The graph also resulted in a positive mathematical function of Y = 6.9065X + 21.137.
In conclusion, the experiment was an adequate investigation that successfully answered the research question of how changing the length of a wire could affect the electrical resistance generated within the wires.
Bibliography
Collins Dictionary. (2020). Retrieved Febuary 24, 2020, from https://www.collinsdictionary.com/dictionary/english/electricity
Electronic Notes. (2020, Febuary 26). What is Resistance? Electrical Resistance. Retrieved Febuary 26, 2020, from Electronic Notes: https://www.electronics-notes.com/articles/basic_concepts/resistance/what-is-resistance.php
Rouse, M. (2014, Febuary 25). TechTarget. Retrieved Febuary 26, 2020, from Resistor: https://whatis.techtarget.com/definition/resistor
Essay Writing Service Features
Our Experience
No matter how complex your assignment is, we can find the right professional for your specific task. Contact Essay is an essay writing company that hires only the smartest minds to help you with your projects. Our expertise allows us to provide students with high-quality academic writing, editing & proofreading services.
Free Features
Free revision policy
$10Free bibliography & reference
$8Free title page
$8Free formatting
$8How Our Essay Writing Service Works
First, you will need to complete an order form. It's not difficult but, in case there is anything you find not to be clear, you may always call us so that we can guide you through it. On the order form, you will need to include some basic information concerning your order: subject, topic, number of pages, etc. We also encourage our clients to upload any relevant information or sources that will help.
Complete the order form
Once we have all the information and instructions that we need, we select the most suitable writer for your assignment. While everything seems to be clear, the writer, who has complete knowledge of the subject, may need clarification from you. It is at that point that you would receive a call or email from us.
Writer’s assignment
As soon as the writer has finished, it will be delivered both to the website and to your email address so that you will not miss it. If your deadline is close at hand, we will place a call to you to make sure that you receive the paper on time.
Completing the order and download