Hooke’s Law
Aim: -To prove Hooke’s law i.e. the extension of the force is directly proportional to the force applied.
– To find the spring constant of the spring.
Apparatus:
Clamp Stand
Helical Spring
Mass Hanger
Pointer
Meter Ruler
Measuring Balance
Method:
-Hang a helical spring from a clamp stand.
-Attach a mass directly to the bottom of the helical spring and record the position of the bottom of the mass hanger relative to a meter ruler.
-Add masses to the spring and record the position of the bottom of the mass hanger.
Safety Precautions:
– Wear safety goggles to prevent any accidents that could occur due to the weights bouncing off the spring.
– Keep a distance from the apparatus.
– Be sure that the spring is tightly attached to the clamp.
– Do not play around with the masses or springs.
Data Collection and Processing
Uncertainty in a measuring balance = ±0.1g
To covert to kg = 0.1÷1000 = ±0.0001kg
Uncertainty in a meter ruler = ±0.05cm
To convert to meters = 0.05 ÷ 100 = ±0.0005m
Formulas
Absolute Uncertainty= Limit of reading÷2
Relative Uncertainty= Absolute Uncertainty ÷ Measured Value
% Uncertainty = Absolute Uncertainty ÷ Measured Value × 100
Force (Newton’s) = Mass (Kg) × Acceleration (ms-²)
Average Extension (cm) = Extension while loading (m) + Extension while unloading (m) ÷ 2
Spring Constant, k (Nm-¹) = Force (Newton’s) ÷ Extension (m)
Elastic Potential Energy (Joules) = 0.5 × Spring Constant × Extension²
Range Of Extension = Extension while loading – Extension while unloading
Random Error = Range of extension ÷ 2
Table 1– Raw Data Table:
Trial No.
Mass
(grams)
±0.1
Mass
(kilograms)
±0.0001
Force Applied
(Newton’s)
F=M×g
±0.0001
Extension While Loading(meters)
±0.0005
Extension While Unloading(meters)
±0.0005
Average Extension =E1+E2÷2 (meters) ±0.001
1
10.2±0.1
0.0102±0.0001
0.100062±0.0001
0.036±0.0005
0.037±0.0005
0.0365±0.001
2
20.4±0.1
0.0204±0.0001
0.200124±0.0001
0.040±0.0005
0.039±0.0005
0.0395±0.001
3
30.6±0.1
0.0306±0.0001
0.300186±0.0001
0.043±0.0005
0.042±0.0005
0.0425±0.001
4
40.8±0.1
0.0408±0.0001
0.400248±0.0001
0.048±0.0005
0.046±0.0005
0.0470±0.001
5
51.0±0.1
0.0510±0.0001
0.500310±0.0001
0.051±0.0005
0.050±0.0005
0.0505±0.001
6
61.2±0.1
0.0612±0.0001
0.600372±0.0001
0.056±0.0005
0.057±0.0005
0.0565±0.001
7
71.4±0.1
0.0714±0.0001
0.700434±0.0001
0.061±0.0005
0.060±0.0005
0.0605±0.001
8
81.6±0.1
0.0816±0.0001
0.800496±0.0001
0.067±0.0005
0.067±0.0005
0.0670±0.001
• Calculations for trial 1
Force (Newton’s) = Mass (kg) × Acceleration (ms-²)
= 10.2±0.1 (g) × 9.81 (ms-²)
= 100.062±0.1 (g)
Covert the g to kg: 100.062 ÷ 1000
= 0.100062±0.0001 (kg)
Average Extension = Extension while loading (cm) + Extension while unloading (cm) ÷ 2
= 3.6±0.05 (cm) + 3.7±0.05 (cm)
= 3.65±0.1cm
In meters = 3.65±0.1cm ÷ 100 = 0.0365±0.001m
Table 2– The range of extension and the random error of the experiment:
Trial No.
Extension While Loading(meters)
±0.0005
Extension While Unloading(meters)
±0.0005
Average Extension =E1+E2÷2 (meters) ±0.001
Force Applied
(Newton’s)
F=M×g
±0.0001
Range of Extension
(meters)
±0.0005
Random Error
(meters)
±0.0005
1
0.036±0.0005
0.037±0.0005
0.0365±0.001
0.100062±0.0001
0.001±0.0005
0.0005±0.0005
2
0.040±0.0005
0.039±0.0005
0.0395±0.001
0.200124±0.0001
0.001±0.0005
0.0005±0.0005
3
0.043±0.0005
0.042±0.0005
0.0425±0.001
0.300186±0.0001
0.001±0.0005
0.0005±0.0005
4
0.048±0.0005
0.046±0.0005
0.0470±0.001
0.400248±0.0001
0.002±0.0005
0.001±0.0005
5
0.051±0.0005
0.050±0.0005
0.0505±0.001
0.500310±0.0001
0.001±0.0005
0.0005±0.0005
6
0.056±0.0005
0.057±0.0005
0.0565±0.001
0.600372±0.0001
0.001±0.0005
0.0005±0.0005
7
0.061±0.0005
0.060±0.0005
0.0605±0.001
0.700434±0.0001
0.001±0.0005
0.0005±0.0005
8
0.067±0.0005
0.067±0.0005
0.0670±0.001
0.800496±0.0001
0.000±0.0005
0.0000±0.0005
•Calculations for trial 1
Force (Newton’s) = Mass (kg) × Acceleration (ms-²)
= 10.2±0.1 (g) × 9.81 (ms-²)
= 100.062±0.1 (g)
Covert the g to kg: 100.062 ÷ 1000
= 0.100062±0.0001 (kg)
Average Extension = Extension while loading (cm) + Extension while unloading (cm) ÷ 2
= 3.6±0.05 (cm) + 3.7±0.05 (cm)
= 3.65±0.1cm
In meters = 3.65±0.1cm ÷ 100 = 0.0365±0.001m
Range Of Extension = Maximum Value – Minimum Value
= 0.037±0.0005 – 0.036±0.0005
= 0.001±0.005 (m)
Random Error = Range of extension ÷ 2
= 0.001±0.005 ÷ 2
= 0.0005±0.0005 (m)
Table 3– Processed Data Table:
Trial No.
Force Applied
(Newton’s)
F=M×g
±0.0001
Average Extension =E1+E2÷2 (meters) ±0.001
Spring Constant, k (Nm)
% Uncertainty
Elastic Potential Energy (Joules)
% Uncertainty
1
0.100062±0.0001
0.0365±0.001
2.74±2.8%
0.0018251825±8.3%
2
0.200124±0.0001
0.0395±0.001
5.01±2.6%
0.0039084263±7.7%
3
0.300186±0.0001
0.0425±0.001
7.06±2.4%
0.0063760625±7.1%
4
0.400248±0.0001
0.0470±0.001
8.52±2.1%
0.0094103410±6.4%
5
0.500310±0.0001
0.0505±0.001
9.91±2.0%
0.0126364880±6.0%
6
0.600372±0.0001
0.0565±0.001
10.6±1.8%
0.01721974±5.3%
7
0.700434±0.0001
0.0605±0.001
11.6±1.7%
0.02122945±5.0%
8
0.800496±0.0001
0.0670±0.001
11.9±1.5%
0.02670955±4.5%
•Calculations for trial 1
Force (Newton’s) = Mass (kg) × Acceleration (ms-²)
= 10.2±0.1 (g) × 9.81 (ms-²)
= 100.062±0.1 (g)
Covert the g to kg: 100.062 ÷ 1000
= 0.100062±0.0001 (kg)
Average Extension = Extension while loading (cm) + Extension while unloading (cm) ÷ 2
= 3.6±0.05 (cm) + 3.7±0.05 (cm)
= 3.65±0.1cm
In meters = 3.65±0.1cm ÷ 100 = 0.0365±0.001m
Spring Constant = Force (Newton’s) ÷ Extension (m)
= 0.100062±0.0001 (N) ÷ 0.0365±0.001 (m)
% Uncertainty for Force = Absolute Uncertainty ÷ Measured Value × 100
= 0.0001 ÷ 0.100062 × 100
= 0.1%
% Uncertainty for Extension = Absolute Uncertainty ÷ Measured Value × 100
= 0.001 ÷ 0.0365 × 100
= 2.7%
Spring Constant = 0.100062±0.1% (N) ÷ 0.0365±2.7% (m)
= 2.74±2.8% Nm-¹
Elastic Potential Energy = 0.5 × Spring Constant × Extension²
= 0.5 × 2.74±2.8% × (0.0365±0.001) ²
= 0.5 × 2.74±2.8% × (0.001332255±5.5%)
= 0.00183±8.3%
Conclusion & Evaluation
Conclusion:
In this experiment, I have been quite successful by proving the aim of the experiment which is Hooke’s Law. The results obtained are slightly incorrect due to any errors as part of the experiment. My calculations were all shown for trial one which whereas follows. In relation to the graph, the line does not pass through the origin as there were uncertainties. The line therefore starts a few cm from the origin on the y axis. The slope in the graph indicates the spring constant. It can be seen that the spring constant value in the graph does not match my result for trial no.1 as I have taken the spring constant value in N/cm. If I take the values in N/m and average all the values of the spring constant from my calculations I will end with a result equal to the gradient or slope of the graph that is 0.227. The units taken for every other value is standard and therefore is correct. My results are reliable as they do result in the Force being proportional to the Extension. I feel that my data is reliable and the graph does show that the extension of the spring directly proportional to the force that is applied to it. We also found that the spring constant and the elastic potential energy increases due to the extension of the spring being proportional to the force.
Evaluation:
I have found that the experiment did have many errors which could have been improved. There were both systematic and random errors involved in the experiment. The meter ruler (uncertainty of ±0.05cm) and the digital balance (uncertainty of ±0.1g) had uncertainty’s which could have altered the accuracy of the results. The experiment also had a parallax error due to the carelessness of me not observing the pointer and the length in the straight path. My equipment was not very accurate as I was given a meter ruler and not an attached ruler. This could have made it very inaccurate as the ruler was leaning over a wall. I could only take one reading per mass, as time management was an issue, which is not reliable as taking more than two readings and averaging the answer will give a more accurate result. The next time I perform this experiment, I will need to make sure that I have at least three readings per mass and should take the average of the three readings to minimize the errors. I should also make sure that the meter ruler is not leaning on a wall and that it is held on by a clamp or that I have the ruler stuck behind the clamp stand. While repeating the experiment one should also put a pointer on the hook to avoid parallax error and get the measurements even more accurate
Essay Writing Service Features
Our Experience
No matter how complex your assignment is, we can find the right professional for your specific task. Contact Essay is an essay writing company that hires only the smartest minds to help you with your projects. Our expertise allows us to provide students with high-quality academic writing, editing & proofreading services.
Free Features
Free revision policy
$10Free bibliography & reference
$8Free title page
$8Free formatting
$8How Our Essay Writing Service Works
First, you will need to complete an order form. It's not difficult but, in case there is anything you find not to be clear, you may always call us so that we can guide you through it. On the order form, you will need to include some basic information concerning your order: subject, topic, number of pages, etc. We also encourage our clients to upload any relevant information or sources that will help.
Complete the order form
Once we have all the information and instructions that we need, we select the most suitable writer for your assignment. While everything seems to be clear, the writer, who has complete knowledge of the subject, may need clarification from you. It is at that point that you would receive a call or email from us.
Writer’s assignment
As soon as the writer has finished, it will be delivered both to the website and to your email address so that you will not miss it. If your deadline is close at hand, we will place a call to you to make sure that you receive the paper on time.
Completing the order and download