2); hence if it is far away then it is smaller (d2> d1). Therefore the mechanical advantage may increase or decrease depending on the distances from the fulcrum.
We can also measure torque (any point of the fulcrum), which refers to the force applied over a distance (lever arm) that causes rotations of the fulcrum. The torque is dependent on three variables: amount of force, angle of application of force and the length of the moment arm/ R. As mentioned above in figure 1, the total torque is equal to zero;. The following formula is used to calculate Torque τ:
Where F is the force (0.71Nm),
R is the distance from the location force is applied to the joint (moment arm) (35cm)
Ï´ is the angle between the force and the radial line
I will now find out the torque for the same question, if the angle is 20°;
This links in with the above statement of the total torque being equal to zero.
I am now going to discuss about the elbow and the forces applied to it. There are many properties which can be used to calculate the forces of the biceps: the angle of the elbow; the length of the upper and lower arm bone; and the distance from the bone to the location the muscle is attached to.
I will now use this formula to find out the force exerted by the biceps (equilibrium) in holding the object, which is the sum of the clockwise moments about any points, equals the sum of the anticlockwise moments about the same point:
Taking 5cm from bone to the biceps attachment;
The force exerted by the biceps holding the object is 891.8N.
Similarly, we can also measure the tension of the bicep/arm holding the object. The image below shows an arm being held out and elevated from the shoulder by the deltoid muscle. The forces can be measured the taking the sum of the torques (of the shoulder joint, the tension (T) can be calculated:
Where W1 is the weight of the arm,
W 2 is the weight of the object
Using the above question; if = 20; the weight of the arm (W1) is 68.6N and the weight of the object (W2) is 49N, then calculate T:
= 113.96N
Therefore the force needed to hold up the bicep/arm at 20, is 113.96N.
Task 2. A) You must complete the energy changes/momentum worksheet. Assessment criteria 2.3,2.4
See attachments
b) You must produce a report that describes the equations of motion needed to calculate the range and maximum height that a projectile thrown by a human can achieve. This report must include examples of both the range equation and maximum height equation. You could use a sports person throwing a ball as an example.
A projectile is any object that has been thrown or shot by a human (measures projectile motion). Projectiles are affected by two factors: gravity (Horizontal motion) and air resistance (vertical motion which is the force of gravity pulling down the object).
As part of this task I am going to carry out various calculations to find out the range and maximum height that a golf ball can achieve when a golf player hits the ball.
A golfer hits a ball so that it moves off with a speed of 37m/s at an angle of 45. I am going to calculate how far the ball goes; the maximum height it will reach; and how long it takes for the ball to get there.
Firstly, I am going to use the following formula to calculate how far the ball travels;
Where R is the range/resultant (how far the ball goes),
V0 is the initial velocity of the ball speed (37m/s)
g is the gravity (9.8m/s) also can be used as (a) since it is constant
Ï´ is angle of the ball (45°)
Therefore;
Hence, when a ball is hit with a speed of 37m/s at 45°, the ball will go far as 139.7m.
Secondly, I will calculate the maximum projectile height (how high a ball will go) by using the following method;
Where Ymax is the maximum projectile height that the ball will go
The maximum projectile height that a ball will reach is 34.9m.
The final calculation that I am going to carry out is the flight time so that I can find out how long it takes for the ball to get there. I will use the following method;
Where Tflight is the time flight of how long it takes for the ball to reach there.
The flight time for the ball to get there is 5.3s.
Using the same question, I now want to find out how far the ball travels horizontally from A to C and the time that the ball is in the air, ignoring any air resistance and taking g = 10ms-2.
Firstly, I will calculate the time that the ball is in the air for, by using the following formula;
I need to find out the vertical motion from A to B first = 90° – 45° = 45°
Formula;
Where v is the final velocity (0 since it is moving horizontally),
u is the initial velocity (37m/s x cos 45) is 26.16m/s
a is the acceleration (10m/s)
t is the time
Therefore;
, so the time it takes from A to C is twice this
I will now look at the horizontal motion from A to C.
Horizontal component of velocity. This is constant during motion.
Horizontal distance = horizontal velocity X time of flight
Therefore the horizontal distance the ball travels from A to C is 136.8m.
Task 3. You must produce a report showing how the variation of blood pressure affects the human body. Your report must include calculations to determine pressure based on area or density values. Assessment criteria 3.1,3.2
Bernoulli’s Principles explains that flowing blood has different speeds and therefore different kinetic energies (KE) at different parts of the arteries. It determines the relationships between the pressure, density and velocity at every point in a fluid. Bernoulli’s Principle was discovered by a Swiss physicist called Daniel Bernoulli in 1738. He has demonstrated that as the velocity of fluid flow increases, its pressure decreases.
Flowing blood has mass and velocity. The mean velocity squared (V2) is equal to the kinetic energy. The image below demonstrates the variance of kinetic energy at different parts of the vessels and also shows the theory of Bernoulli’s Principle:
Therefore KE = ½ mV2. As we know from above that blood flows inside arteries, were pressure is applied laterally against the walls of the vessel which is known as the potential or pressure energy (PE). The total energy (E) of the blood pressure within the artery is the sum of the kinetic and potential energies (presuming there are no gravitational effects):
E = KE + PE(where KE ∝ V2)  Therefore,E ∝ V2 + PE
Similarly, Bernoulli’s Principle states that the sum of the Pressure (P), the kinetic energy per unit volume (1/2 pv2), and the gravitational potential energy per unit volume (pgy) has the same value at all points along a streamline. The equation below shows this:
There are two vital theories that follow from this relationship, which includes:
Blood flow driven by the variation in total energy between two points. Normally, pressure is considered as the driving force for blood flow but in fact it is the total energy that moves flow between two areas (i.e. longitudinally along a blood vessel or across a heart valve). KE is relatively low in most of the cardiovascular system; hence PE difference is the energy that drives flow. Similarly, is KE is high then the total energy increases which explains the flow across the aortic valve during cardiac ejection. This is because, as KE drives blood across the valve at a very high velocity, it ensures that the total energy (E) in the blood crossing the valve is higher than the total energy of the blood more distal in the aorta.
KE and PE can be converted to maintain the total energy unchanged, which is the basis of Bernoulli’s Principle. This principle is basically about the blood vessel that is suddenly narrowed then returned to its normal diameter. The velocity increases as the diameter decreases in narrowed region (stenosis). Blood flow (F) is the mean velocity (V) and the vessel cross-sectional area (A) is directly related to diameter (D) (or radius, r2); hence V ∝ 1/D2. If the diameter is reduced by half in the region of the stenosis, the velocity increases 4-fold, due to KE ∝ V2, hence KE increases 16-fold. The image below demonstrates this:
The image above shows the total energy being conserved within the stenosis (E actually decreases because of resistance), then the 16-fold increase in KE will decrease in PE. Once past the narrowed segment, KE will go back to its pre-stenosis value as the post-stenosis diameter is the equal to the pre-stenosis diameter, hence flow is conserved. Due to the resistance of the stenosis and turbulence, the port stenosis PE and E will both fall. Therefore, blood flowing at greater velocities has greater ratio of KE to PE.
Find Out How UKEssays.com Can Help You!
Our academic experts are ready and waiting to assist with any writing project you may have. From simple essay plans, through to full dissertations, you can guarantee we have a service perfectly matched to your needs.
View our services
As we know, blood pressure is the force of fluid against the walls of the arteries, similar to how water exerts the pressure inside aplastic pipe. It is made up of systolic and diastolic pressure. Systolic pressure is the top figure and relates to when the heart is contracting (beating) and forcing blood through the arteries and transporting it to the rest of the body i.e. brain, kidneys etc. The normal values for systolic pressure is from 120-139mmHg. Diastolic pressure is the bottom figure and is linked to when the heart is relaxing. The normal value for diastolic pressure is between 80-89mmHg. Hence, if the values exceed these numbers, then it is considered to be hypertension.
Hypertension is high blood pressure which is caused by the increased force of blood flowing through the arteries. Healthy arteries are flexible, strong and elastic. Inner lining of the arteries are smooth allowing the blood to flow freely, supplying important organs and tissues with adequate nutrients andoxygen. Hypertension can gradually lead to wide range of problems such as damaging the cell’s inner lining of the arteries; hence releasing a cascade of events that causes the artery wallsthick and stiff (called arteriosclerosis), or hardening of the arteries. Similarly, the fats from the diet enter the bloodstream and passes through the damaged cells. However, plaques are prone to building up in the arteries leading to atherosclerosis. These changes lead to blocking blood flow to the heart, kidneys, brain, arms and leg.
Heart: it causes coronary artery disease, which is narrowing of the arteries that doesn’t allow blood to flow freely through the arteries. Leading to chest pain, heart attack (myocardial infarction)or irregular heart rhythms (arrhythmias). Hypertension can also cause enlarged left heart as the pressure forces the heart to work harder than necessary. Similarly, overtime the strain on the heart leads to the heart muscles to weaken and work less effectively causing the heart to wear out and fail.
Brain: – hypertension can cause mini-strokes (Transient ischemic attack (TIA)), which a temporary disruption of blood supply to the brain caused by blood clot or atherosclerosis. Similarly, it can lead to the full-blown stroke which happens when part of the brain is deprived of oxygen and nutrients leading brain cells to die. Uncontrolled hypertension damages and weakens the brain’s blood vessels, causing to narrow, rupture or leak. Narrowing and blockage of the brain’s blood vessels can also lead to Dementia and mild cognitive impairment.
Kidneys: – filters excess fluid and waste from the blood via a process that depends on healthy blood vessels. Hypertension can damage both the blood vessels and leading to the kidneys. This leads to various kidney diseases, failure and scarring of the kidney.
Eyes:- Blood vessels supplies blood to the eyes; hence high blood pressure can damage the blood vessel (retinopathy)
Reference http://www.bhf.org.uk/heart-health/conditions/high-blood-pressure/blood-pressure-research.aspx 22nd October 2013
http://www.bhf.org.uk/heart-health/conditions/high-blood-pressure.aspx 22nd October 2013
http://www.webmd.boots.com/hypertension-high-blood-pressure/guide/diastolic-systolic 24th October 2013
http://edition.cnn.com/HEALTH/library/high-blood-pressure/HI00062.html 24th October 2013
http://amazinghumanbody-prakash.blogspot.co.uk/2009/10/skeletal-system.html 25th October 2013
http://www.bbc.co.uk/science/humanbody/body/factfiles/armandshoulder/arm_and_hand.shtml 26th October 2013
http://www.cvphysiology.com/Hemodynamics/H012.htm 26th October 2013
http://www.bu.edu/gk12/kai/Lesson%206/BP_Back.pdf 27th October 2013
http://mysite.verizon.net/fvozzo/genphys/lecture.html 27th October 2013
http://muscle.ucsd.edu/musintro/ma.shtml 29th October 2013
http://www.as.wvu.edu/~rbrundage/chapter8b/sld015.htm 29th October 2013
http://www.answers.com/topic/projectile-motion 30th October 2013
http://www.wired.com/wiredscience/2011/10/optimizing-a-basketball-shot/ 1st November 2013
http://demoweb.physics.ucla.edu/node/28 25th November 2013
http://www.medicalphysics.org/apps/medicalphysicsedit/WebPOTB.pdf 25th November 2013
http://physics.eou.edu/opensource/physics/projectile.pdf 27th November 2013
http://www.google.co.uk/url?sa=t&rct=j&q=&esrc=s&source=web&cd=14&ved=0CG8QFjAN&url=http%3A%2F%2Fwww.wooster.edu%2F~%2Fmedia%2Ffiles%2Facademics%2Fresearch%2Fhhmi%2Fresources%2Flectures%2Fhuman-arm-goniometer.ashx&ei=bnakUuzDC6yg7AbX5oGYCQ&usg=AFQjCNFMTH1EmPzRvKvptZu4R7_XUpFKPw&bvm=bv.57752919,d.ZGU 28TH November 2013
Dobson et al. (2002). ‘ Collin advanced – Physics’. Collins eduction : London
Rounce, J.F and Lowe, T.L. (1992). ‘Calculations for A level Physic’. Second edition. Stanley Thornes: Britain
Boutal et al. (2008). ‘AS-Level physics – exam board’. Coordination group publications CGP: Newcastle
Tsokos, KA. (2008). ‘Physics for the IB Diploma’. Fifth edition. Cambridge university press: united kingdom
Johnson et al. (2000). ‘Advanced physics for you’. Nelson Thornes: united kingdom
Essay Writing Service Features
Our Experience
No matter how complex your assignment is, we can find the right professional for your specific task. Contact Essay is an essay writing company that hires only the smartest minds to help you with your projects. Our expertise allows us to provide students with high-quality academic writing, editing & proofreading services.
Free Features
Free revision policy
$10Free bibliography & reference
$8Free title page
$8Free formatting
$8How Our Essay Writing Service Works
First, you will need to complete an order form. It's not difficult but, in case there is anything you find not to be clear, you may always call us so that we can guide you through it. On the order form, you will need to include some basic information concerning your order: subject, topic, number of pages, etc. We also encourage our clients to upload any relevant information or sources that will help.
Complete the order form
Once we have all the information and instructions that we need, we select the most suitable writer for your assignment. While everything seems to be clear, the writer, who has complete knowledge of the subject, may need clarification from you. It is at that point that you would receive a call or email from us.
Writer’s assignment
As soon as the writer has finished, it will be delivered both to the website and to your email address so that you will not miss it. If your deadline is close at hand, we will place a call to you to make sure that you receive the paper on time.
Completing the order and download