Manufacturing processes Free Essay Example

The Importance of DFM, DFMA and SPC to Manufacturing Procedures

Section one

Design for Manufacturing ( DFM ) is the practical planning of how merchandises are traveling to be manufactured with the intent of optimising all maps attached to the fabrication procedure and this include, cost of production, quality and other procurance services.Through this attack, resources like clip and cost to be spent on fabrication procedure, is greatly minimized. For case, when planing electronic constituent, manufactures specify tolerance degree of around 0.5 or any value.

The purpose if this is to avoid investing resources and clip with an purpose of accomplishing 100 % quality. As a consequence, these excess resources are channeled to other procedures, therefore salvaging them ( Anderson, 8 ) .

There are seven rules of an optimum cost effectual design. First is, cut downing the figure of parts used in fabrication. This efficaciously reduces the fabrication cost. The fewer the figure of parts, the lesser the purchases, managing, assembly trouble, service review and testing. A portion which is non dependent in footings of comparative gesture to other parts ought non to be manufactured with a different stuff.

The constituents that make the assembly or service of other parts highly hard or impossible should be removed. Manufacturing procedure such as mold of injections and pulverization metallurgy are meant to cut down cost this is because designs from such process consist on minimum stuffs.

Second, the development of a modular design: The acceptance of a modular based design of a merchandise saves clip and once more AIDSs fabrication.

It is a flexible design attack where a merchandise is updated by redesigning the fabrication procedure. Furthermore, modular design attack aid to run trials before the concluding assembly is created. This allows the use of the standard constituents to minimise merchandise disagreements. A reverse of this factor could be the connexion in footings of application. Harnessing standard constituents has proved to be more cost effectual in DFM.

The 3rd rule is planing of multi functional parts. Multi functional parts refer to parts which are manufactured to offer more than one map. Planing multi functional parts cut down the entire figure of parts

to be used in a design and fabrication procedure. This attack is analogized to killing two birds with a individual rock. An illustration of multi-functional portion design attack is an electrical music director. An electrical music director acts as a structural member and besides as a heat dispersing component.

Fourthly, planing parts for easiness of fiction. Planing a merchandise which is easy to fabricate is another rule of design for fabrication. The object to be designed is critically examined and to place which stuffs can be used to do the design. Afterwards a methodological analysis, of choosing the best combination of stuffs and fabrication procedure, is employed in order to cut down the fabrication cost ( Priest, John and nchez, 11 ) . Artistically, alluring processs such as picture and machining should be avoided as they are deemed as waste resources and merely add cost to DFM.

The 5th rule is, avoid separate fasteners. Fasteners ever increase the cost of fabrication. In add-on to that, operations that involve fasteners are non 100 % successful, therefore they cut down the efficiency of the fabrication procedure. If fasteners have to be used, so some ushers should be followed for choosing them. This usher aims at minimising the figure, size and fluctuation used every bit good as using standard constituents where possible. Prison guards that are excessively long or excessively short should be avoided. Likewise separate washers, tapped holes, and unit of ammunition caputs and flatheads should be used.

The 6th rule is, make the most of conformity. During interpolation operations, due to differences in portion dimensions or truth of positioning device, mistakes can arise leadingto harm ofa portion or to the full equipment. Therefore, it is indispensable to include conformance in the portion design and in the assembly procedure. This

can be attained through accurate measuring. For case, when one is fabricating a shaft and hole tool, accurate measuring will enable the shaft tantrum into the hole without damaging it.

Finally, cut downing the figure of times of managing. Handling is a common term that is used to depict placement, pointing and repairing activity of a designed portion or constituent. The procedure of planing constituents

That required minimal handling is another rule of an effectual design for fabrication scheme. One manner to minimise handling is to plan symmetrical and flexible designs that are easy to put or East.

Any constituent, for case, people, stuff, environment, that has the ability to bring forth an end product, is called a procedure. It is good to observe that these factors are capable to fluctuations due to assorted grounds. As a consequence, they have to be good monitored if a coveted quality of merchandises is to be attained therefore statistical procedure control ( SPC ) tool come in ready to hand. SPC, as an analytical tool, enables one to place defects within a procedure so that right betterments can be made where necessary. The most normally used attack in doing betterments is measurings. However, in most designs, measurings used are non based on the international criterions ( Chowdhury, 10 ) . Therefore, there is a demand for organisations like the International Organization for Standardization ( ISO ) and others to develop measurings that are globally acceptable.

Six Sigma is a SPC concern enterprise direction tool foremost introduced by Motorola in the early 1990s and it assists in placing the quality divergence a merchandise. The construct of Six Sigma has evolved over the last twosome of old ages. Six Sigma has a actual, conceptual, and practical definitions and it can be viewed from a metric, methodological analysis every bit good as the direction system.

In Six Sigma, procedure disparities and merchandise or service defects are scaled down by extended usage of statistical techniques. These statistical techniques employ the usage of tool such as control charts, design of experiments, and response surface methodological analysis among others. While describing the procedure betterment,

certain numeral values, herein referred as Six Sigma Metrics, such as Defects per Million Opportunities ( DPMO ) , are used. Therefore, Six Sigma was ab initio started as a defect decrease attempt in fabrication and was so applied to other concern procedures for the same intent. The application of Six Sigma as a direction system extremely improves the public presentation of a given system.

CP and CPK are proficiency statistics, which enable one evaluated the procedure of a given specification. They are really effectual tools every bit far as choice direction in involved. Before planing a peculiar merchandise or design, it is ever good to put the criterion or the quality of the merchandise one wants to get. This is made possible by these two statistical tools. Every merchandise produced has boundaries defined as upper bounds and lower bounds. In DFM, these bounds are referred to as uppers and lower specifications severally, and this bounds is efficaciously determined utilizing CP ( Whitehouse, 13 ) . In add-on to that, quality of a merchandise can besides be measured by ciphering its sample mean and standard divergence. Standard divergence enables one to cognize the grade of fluctuation the designed merchandise is from the sample mean and CPK aids in mensurating them.

The procedure of fabricating to a great extent relies on chance. The result of the merchandise can non be accurately predicted. In order to turn to such jobs, computing machine simulations can be used to pattern the procedure of fabrication and enable the industries come up with optimized ways of accomplishing a procedure efficaciously and expeditiously. The intent of the simulation is to enable the abstract combination of stuffs without physically executing the existent procedure. This helps minimise hazards involved in fabricating uncertainnesss.

Section two

Geometry is the art of stand foring information utilizing diagrams and symbols. In technology, fluctuations, between characteristics, has to be allowed so that truth can be achieved ( Kenneth, 14 ) . The tabular array below shows some common geometric tolerance symbols and their maps.

Section three

ISO criterions are criterions unit of measuring which are used in any technology work. These criterions were foremost implemented in the twelvemonth 1994 as a common units for all technology model. This was a step taken to guarantee that applied scientist do non come up with their ain measuring methods, but adhere to one common unit of measuring that was to be used globally ( Bralla, 16 ) .

In order to understand the construct if ISO measurings see this illustration. The measuring in the tabular array below are taken from a micron prison guard gage. How do assorted criterions better the measuring and hence addition assurance in measurement Lashkar-e-Taiba see a series of measurings of amulct turned shafts utilizing a micron and corresponding uncertainness associated in measurings as given in table 1.1 below.

In the above tabular array the value U=7.6 & A ; mu ; m is the diameter tolerance of work piece calculated

Thorough meteoric criterions ( ISO-14253-1 ) . This value means that the diameter tolerance of work. The piece must be reduced byto take history the uncertainnesss associated with a series of measurings and how they can be removed through slandered meteoric measurings that enhance assurance in measurings.

Shaft-based ISO criterions are criterions in which the dimensions of the shaft are included as a bound of the measurings, that is, the hole is normally bigger than the shaft. On the other manus, in hole-based criterions, the bounds of measuring are non an inclusion of the basic size, that is, the size of the hole is smaller than the Shaft ( Hoffman, McCauley and Hussain, 6 ) . When piecing two parts together, there must be a scope of stringency that is allowed between the two parts, this scope is what is called a tantrum. Discussed in the subsequent paragraphs, are the three chief types of tantrum and how they can be used. They are, clearance, intervention sliding and fit severally.

A clearance tantrum is a tantrum in which one portion, the shaft, fits into another portion, the hole, and leaves a clearance spread. In this instance, the hole is normally bigger than the shaft. This sort of tantrum can be best used to do pulley systems ( Tennant, 4 ) .The 2nd tantrum is the intervention tantrum which is defined as a tantrum in which one portion, particularly the shaft, is larger than the hole and hence force must be used to suit them together.Finally the sliding tantrum, this is a tantrum in which when it is loose it provides clearance tantrum and when it is tight it gives manner to an intervention tantrum. It is largely used to place shafts that are compatible with one another.

As to the decision, minimising the cost of production while keeping quality of merchandise is really good to a concern or a company. DFM is a tool that enable monitoring constituents of production while seting them to acquire the best end product. Coupled with utile statistical control tools like SPC, CP and CPK, more efficiency for better end product, is attained. Finally, with DFM, high rate of production is achieved this is because the chief focal point is fabricating merchandises easy.

Mentions

Anderson, D. M. ( 2010 ) .Design for Manufacturability and Concurrent DesignWaless: CIM Press.

Chowdhury, S. ( 2003 ) .Design for Six Sigma.London: Prentice Hall.

Hoffman, E. G. , McCauley, C. J. , and Hussain. M. I. ( 2000 ) .Shop Reference for Students and Apprentices from Machinery Handbook( 2^neodymiumEd. ) . New York: Industrial Press.

Kenneth, D. P. ( 2011 ) .Fabrication and Assembly Manufacturing and AssemblyDFMA New York: Prentice Hall.

Tennant, G. ( 2001 ) .Six Sigma: SPC and TQM in Manufacturing and ServicesAldershot: Gower Publishing Limited.

Whitehouse, D. ( 2003 ) .Handbook of Surface and NanometrologyBristol: Institute of Physics Publishing.

Bralla J. G. ( 2006 ) .Handbook for merchandise design for fabrication: a practical usher to low-priced production. McGraw-Hill

Priest, John W. , and J. M. nchez. ( 2001 ) .Product development and design for fabrication: A collaborative attack to producibility and dependability.Marcel Dekker.