The purpose of the “Characteristic of Hydrates” lab is to study hydrates, and have the ability to recognize them. This lab also concentrates on observing the reversibility of hydration reactions by hydrolysis, and also evaluating compounds for efflorescence of deliquescence.
A.Identification
1. Place 0.5 grams of each substance (Nickel Chloride, Potassium Chloride, Salt Tetraborate, Sucrose, Calcium Carbonate, and Barium Chloride) in a little dry test tube. 2. Heat carefully with a burner flame and observe carefully. If droplets of water appear on the test tube it may be a hydrate.
Note the nature and color of the residue. 3. Let television cool, and try to liquify the residue in a couple of cm3 of water, warming if essential. A true hydrate will liquify in water, producing a color similar to that of the original hydrate. A carb will emit water, but tends to char. The residue will likewise typically be a caramel color.
B.Reversibility
1. Carefully heat a couple of crystals of about 0.
3 grams of hydrated Cobalt( II) Chloride, CoCl2 x 6H2O in a vaporizing meal until the color change appears to be complete 2. Liquify the residue in the evaporating meal in a couple of cm3 of water from the wash bottle 3. Heat the residue to a boiling and carefully boil it to dryness. Note any color modifications. 4. Put the vaporizing meal on the laboratory bench and let it cool.
C.Deliquescence and Efflorescence
1. Place a few crystals of Na2CO3 x 10H2O, CaCl2, KAl(SO4)2 x 12 H20, and CuSO4 in an a different evaporating dish next to the CoCl2 prepared in part B.
2. To see weather condition the samples got or lost mass, weigh each of them on a top-loading balance and record to the nearest hundredth. 3. Weight them again after an hour to spot ANY changes in mass. 4. Observe the samples occasionally. Keep in mind any structures in color and structure and degree of moisture.
D. Percent of Water in Hydrate
1. Clean crucible and its cover, and also make sure that crucible tongs are clean. Put over fire, and let cool. 2. Weight the crucible to the nearest thousandth. Handel with tongs 3. Obtain a sample of an unknown hydrate, and place about 1 gram in the crucible. 4. Weight the crucible, cover and sample on the balance. 5. Put the crucible on the clay triangle, with the cover off center to allow water vapor to escape. 6. Heat again, gently at first, and then with the bottom red for about 10 minutes. 7. Center the crucible cover, and let it cool to room temperature. 8. Weight the cooled crucible and with its cover and contents. 9. Examine the solid residue.
10. Add water until the crucible it two thirds full. Warm gently if the residue doesn’t readily dissolve. 11. Does the residue appear to be soluble?
Waste Disposal:
Dispose of the Copper mixture, and the Aluminum mixture in the correct bowl under the waste hood. All of the acids and bases can be disposed of down the sink. If the compound isn’t water soluble put in the organic container.
Chemical Principles in the Laboratory: Experiment 6
The purpose of the Properties of Hydrates lab was to be able to identify if a substance was a hydrate or not. In lab, experiments where conducted to see if a compound was a hydrate or not. In order for the compound to be deemed as a hydrate it had to:
1. Release water upon heating
2. The anhydrous residue had to be water soluble
3. Exhibit reversibility
If, and only if the compound showed that it could exhibit all three of these properties, could it be distinguished a hydrate. In part “A” of the experiment, Nickel Chloride and Sodium Tetraborate were the only two compounds that were true hydrates. Both of these showed water residue when heating, where soluble in water after heating, and converted back to it original color after performing the first two experiments. Some of the other compounds had positive results for one or two test but not all three. For example, Sucrose, when heated, water residue appeared on the test tube, and was soluble in water, but the compound didn’t show reversibility.
In part “B” of the experiment, CoCl2*6H2O was heated, dissolved, and then heated again to show that it was a true hydrate. When the Cobalt Chloride was heated, it turned from the color of fuchsia pink, to a light blue. And then after being dissolved into water, the compound turned back to its original color of fuchsia pink, demonstrating reversibility. The color change in this compound shows that by adding water to the anhydrous residue, that the same bonds that were broken my dehydrating the compound where reformed when adding water.
In part “C”, four compound, plus the Cobalt Chloride mentioned above were tested for deliquescence, and efflorescence. Only one compound turned about to be efflorescent, which means that it lost water, which was Sodium Carbonate. The compounds mass before sitting out was 50.645g, after being exposed to the conditions of the laboratory for an hour, the sample weight 50.603g losing approximately 0.042g over the period of an hour. The Calcium Chloride (gained 0.258g), Copper Sulfate (gained 0.007g) and Cobalt Chloride (gained 0.068g) where all deliquescent, meaning that again mass while sitting in the laboratory. The Potassium Aluminum sulfate, exhibited stability while sitting out for an hour, neither gaining nor losing mass.
For part “D” of the experiment, the percent of water in the unknown hydrate was %12.290. The closet percent of the given facts of the unknown was Barium chloride (BaCl2*2H2O), which has %14.8 water in it. This percent was found by using the formula below: % water in hydrate=(mass of water in hydrate/mass of the entire hydrate)
The wide range of difference between the percent of the given and the unknown could have been due to the fact that there was wood debris in the unknown sample . This could have thrown off the amount of water present in the sample, and messed up the amount of water able to evaporate.
Essay Writing Service Features
Our Experience
No matter how complex your assignment is, we can find the right professional for your specific task. Contact Essay is an essay writing company that hires only the smartest minds to help you with your projects. Our expertise allows us to provide students with high-quality academic writing, editing & proofreading services.
Free Features
Free revision policy
$10Free bibliography & reference
$8Free title page
$8Free formatting
$8How Our Essay Writing Service Works
First, you will need to complete an order form. It's not difficult but, in case there is anything you find not to be clear, you may always call us so that we can guide you through it. On the order form, you will need to include some basic information concerning your order: subject, topic, number of pages, etc. We also encourage our clients to upload any relevant information or sources that will help.
Complete the order form
Once we have all the information and instructions that we need, we select the most suitable writer for your assignment. While everything seems to be clear, the writer, who has complete knowledge of the subject, may need clarification from you. It is at that point that you would receive a call or email from us.
Writer’s assignment
As soon as the writer has finished, it will be delivered both to the website and to your email address so that you will not miss it. If your deadline is close at hand, we will place a call to you to make sure that you receive the paper on time.
Completing the order and download